Liugong Tc600c5 55 Ton 60 Ton Hydraulic Mobile Truck Crane
Features:
1. The largest crane operating range, and the most optimal lifting performance in the industry.
2. Five-section U-shaped boom of large cross section with maximum length reaches up to 45m and jib of the length of 16 m.
3. The 7.5m transverse outrigger span with a fixed counterweight of 3.3t makes its lifting performance 5-10% higher than that of the products of same class.
4. Cum-mins ISLe series high pressure common rail large torque euro III engine of 340 horsepower is configured.
5. The combination of Fast 9-speed gearbox and double reduction axle features large speed ratio range, which meets the requirements of low gradeability speed and high traveling speed.
6. The max. traveling speed is 85km/h and max. gradeability is up to 46%.
7. Load sensitive valve compensation technology, with stable control.
Main Specifications
| Model |
TC600C5 |
| Max Lifting weight |
55 t |
| Max. Lifting height |
62 m |
| Max. Lifting moment |
2033 kN.m |
| Engine model |
D-Cum-mins ISL9.5-340E51A |
| Engine power |
251kW |
| 5-section boom |
45.6 m |
| Min. turning diameter |
24 m |
| Max. vehicle speed |
85km/h |
| Max. grade ability |
47% |
| Outrigger span |
7.5*5.75 m |
| Dead weight in driving |
43.4 t |
| Dimension |
13950*2800*3730 mm |
A mobile crane is a cable-controlled crane mounted on crawlers or rubber-tired carriers or a hydraulic-powered crane with a telescoping boom mounted on truck-type carriers or as self-propelled models.They are designed to easily transport to a site and use with different types of load and cargo with little or no setup or assembly.
Larger, heavier duty, purpose-built "truck-mounted" cranes are constructed in two parts: the carrier, often called the lower, and the lifting component, which includes the boom, called the upper. These are mated together through a turntable, allowing the upper to swing from side to side. These modern hydraulic truck cranes are usually single-engine machines, with the same engine powering the undercarriage and the crane. The upper is usually powered via hydraulics run through the turntable from the pump mounted on the lower. In older model designs of hydraulic truck cranes, there were two engines. One in the lower pulled the crane down the road and ran a hydraulic pump for the outriggers and jacks. The one in the upper ran the upper through a hydraulic pump of its own. Many older operators favor the two-engine system due to leaking seals in the turntable of aging newer design cranes.
Generally, these cranes are able to travel on highways, eliminating the need for special equipment to transport the crane unless weight or other size constrictions are in place such as local laws. If this is the case, most larger cranes are equipped with either special trailers to help spread the load over more axles or are able to disassemble to meet requirements. An example is counterweights. Often a crane will be followed by another truck hauling the counterweights that are removed for travel. In addition some cranes are able to remove the entire upper. However, this is usually only an issue in a large crane and mostly done with a conventional crane such as a Link-Belt HC-238. When working on the job site, outriggers are extended horizontally from the chassis then vertically to level and stabilize the crane while stationary and hoisting. Many truck cranes have slow-travelling capability (a few miles per hour) while suspending a load. Great care must be taken not to swing the load sideways from the direction of travel, as most anti-tipping stability then lies in the stiffness of the chassis suspension. Most cranes of this type also have moving counterweights for stabilization beyond that provided by the outriggers. Loads suspended directly aft are the most stable, since most of the weight of the crane acts as a counterweight. Factory-calculated charts (or electronic safeguards) are used by crane operators to determine the maximum safe loads for stationary (outriggered) work as well as (on-rubber) loads and travelling speeds.
Truck cranes range in lifting capacity from about 14.5 short tons (12.9 long tons; 13.2 t) to about 2,240 short tons (2,000 long tons; 2,032 t). Although most only rotate about 180 degrees, the more expensive truck mounted cranes can turn a full 360 degrees.
Company Information
Audited Supplier 
){kind=link}
){kind=link}